Windshield repair fluid | Crack automotive glass repair fluid | Auto Glass Repair Tools | Automotive glass repair fluid | Restorative | Car Windshield Repair Agent | Crack crack reducing liquid glue | Tool Sets - Dual-Use Glass Repair Tools(6161)

產品類別：玻璃修復液
材質： ABS
功能：用於修復2cm以內的玻璃裂縫
淨重：55.8g
包裝尺寸：13.2*11*2cm
毛重：71.2g

HK$78.00

HK$45.00

{{shoplineProductReview.avg_score}} {{'product.product_review.stars' | translate}} | {{shoplineProductReview.total}} {{'product.product_review.reviews' | translate}}

{{amazonProductReview.avg_rating}} {{'product.product_review.stars' | translate}} | {{amazonProductReview.total_comment_count}} {{'product.product_review.reviews' | translate}}

The maximum quantity per submit is 99999

This quantity is invalid, please enter a valid quantity.

Sold Out

Please message the shop owner for order details.

Description

★ Aircraft special-shaped syringe glass repair tool, center and tail work area design, for repairing windshield edge breakage, a wider range of repair;
★ The repair solution is injected through the vacuum exhaust pipe of the syringe to exhaust the air, and the repair is more thorough, and the glass will not be broken twice;
★ No dead angle repair, the range is up to 95%, two-point positioning hole design, the edge of the windshield can also be repaired;
★ Our formula is thin and easy to inject into cracks, but thick enough to restore the windshield's previous strength;
★ SPECIALIZING IN THE TREATMENT OF SPOT DAMAGE, GLASS REPAIR CAN ONLY BE USED ON SINGLE-LAYER DAMAGED WINDSHIELDS WITH A DIAMETER OF LESS THAN 2CM.

Packing list
Windshield repair (1 set)

to explain
How to Use:
Clean:
1. Find the broken place and use a needle to remove the broken glass.
2. Drop a few dots of repair liquid to cover the surface of the damaged mouth.
Mounting Bracket:
1. Align the center point of the positioning bracket with the damaged port, press the suction cup to install it firmly.
2. Drop a few points of repair liquid at the silica gel of the pressure cylinder, and immediately screw the pressure cylinder into the positioning bracket, and the glass is not loosened.
Evacuation and exhaust:
1. Hold the pressure cylinder, slowly unscrew the pressure rod, keep it for about 10 minutes to vacuum, and extract the air from the damaged area.
2. Unscrew out the pressure rod and drop 1-2 drops of repair solution into the pressure cylinder.
Pressurized osmosis:
1. Insert the pressure bar, then slowly screw into the pressure cylinder and hold for 10 minutes to pressurize.
Go to the 45° angle inside the car and observe that the glass damage disappears, and the penetration is completed. Then remove the suction cup pressurization tool.
Note that if the effect is not good, you can repeat the vacuum pressurization process without curing, once cured, it cannot be repaired again.
Curing:
1. Drop a drop of repair solution under the damaged hole, cover with a curing film, scrape off the bubbles with a blade, and move the car to direct sunlight for 10-30 minutes or replace it with an ultraviolet lamp until it is cured.
2. Peel off the curing film and scrape off the excess resin.
3. If there are residual fog spots, drop as little repair solution as possible in the fog spots, cover the curing film and fit naturally, and do not touch it with anything.

Notes:
*This product contains methacrylates, and a high concentration of odor may cause tearing.
*Avoid contact with eyes, skin and clothing.
*In case of contact with eyes or skin, rinse immediately with plenty of water. If the irritation persists, go to the clinic/hospital, immediate treatment is necessary.