Instructions
Before use and installation, please read the product instruction manual carefully
Installation instructions: 1. Take the electric wheelchair out of the box, hold the push handle with one hand, and press the front seat frame of the seat downward with the other hand until the seat and backrest are 90 degrees, until the lock is locked in place, so that the seat and the frame are combined. one
2. The installation and retraction of the movable hanging feet. Installation: Put the hanging feet down to the bottom. Folding: Fold the seat cushion in half and then fold the hanging legs
3. Installation and disassembly of the anti-roll wheel: Press the marble of the anti-roll wheel with your fingers and insert it into the tube hole until it is confirmed that the marble is locked in the hole of the marble. Grab the anti-roll wheel with your hand and pull it backwards. Anti-roll wheels must be installed when using
4. Insert the controller lever into the holder and insert the cable into the cable
5. When charging and using, please press the switch "-" ("One" is on, "O" is off). If it is not used for a long time, please press the switch "O". If it is not used for a long time, it must be plugged in and charged once a month. (Do not allow the battery of the electric wheelchair to be stored in a power deficit)
Instructions for use:
1. Turn up the pedals, put the pedals down after getting on the electric wheelchair. Note: Do not step on the pedals to get off and on the electric wheelchair, as this may cause the electric wheelchair to tip over.
2. After getting on the electric wheelchair, please fasten your seat belt. Turn on the controller power button. The indicator light will be on, at this time the joystick should be in the middle position, push the joystick, the electric wheelchair will start running
3. The steering wheel can control the direction and speed at the same time. Slowly push the steering wheel in the direction of travel, and the electric wheelchair will start to travel.
4. To stop the running electric wheelchair, just release your hand to reset the joystick, and press the parking brake to achieve smooth parking.
5. When parking on a slope, please use the lowest level (first gear) when going downhill, and use the highest gear (third gear) to release the control handle when going uphill. If the strength of the electromagnetic brake is not enough, you need to use the manual brake parking device (Press the manual brake parking brake on both sides at the same time)
6. The speed adjustment button of the controller can adjust the speed of the electric wheelchair. The user should choose the maximum speed of the electric wheelchair according to their physical condition and road conditions. Speed display: default first gear when starting, if you need high power or high speed, please press the speed adjustment "←", so that the three speed display lights are all on. For small power or low speed, please adjust by speed
7. When pushing the electric wheelchair by hand, first turn off the control handle and then turn off the main power switch (press 0) to easily push the electric wheelchair
8. The electric wheelchair is suitable for driving on a flat road, and the transmission mechanism and control system of the electric wheelchair will be damaged on muddy, potholes and uneven roads.
9. Before getting off the car, first turn off the power of the controller, press the parking brake, then turn the foot pedal up, and then get off the car
Precautions
1. Do not put your fingers in the gap when pressing down on the seat cushion to avoid injury
2. Do not ride in a wheelchair when the standing brake is not applied to avoid bodily injury caused by the wheelchair sliding
3. Do not step on the pedals to get off and on the wheelchair, to prevent the wheelchair from leaning forward and causing bodily injury
4. Do not hold other parts to lift the wheelchair to avoid damage to the wheelchair or bodily injury
5. When going downhill, do not use the standing brake to avoid personal injury caused by rollover
6. When getting off the bus, be sure to brake the standing brake first. The standing brake is used when the user gets on and off the wheelchair or when parking, and cannot be used for braking while driving.
Care and Maintenance
a. Before using the wheelchair, check the screws of the front wheel, rear wheel, standing brake and other parts and the rear wheel spokes. If they are loose, please tighten them (due to bumps in transportation, etc., the screws of the wheelchair may become loose).
b. Check whether the inflation after the car is normal. If the air is insufficient, please inflate in time. The inflation method is the same as that of the bicycle.
c. During the use of the wheelchair, it is necessary to check the movement of various parts, whether the screws and the spokes of the rear wheel are loose every month. If it is loose, lock it in time to avoid potential safety hazards.
d. The active parts should be lubricated every week to prevent inflexible activities
e. After using the wheelchair, use a soft dry cloth to wipe the surface water vapor, dirt, etc. to prevent rust. f. The wheelchair should be stored in a dry place to avoid moisture and rust. 1. The seat cushion and night should be kept clean to prevent Breeding bacteria g. Use period: From the date of purchase, the safe use period is 5 years
